LS G-Series G3033, G3033H, G3038 & G3038H Hardtop Cab 11826
Keep using your LS G-Series tractor when the weather turns bad. Original Tractor Cab 11826 is a model-fit hardtop cab for the LS G3033, G3033H, G3038, and G3038H compact tractors.
A hard ABS plastic roof gives you firm cover from above. Meanwhile, clear shatter-resistant Lexan panels help you see the work area while the enclosure helps block rain, snow, sleet, and cold wind.
Hinged doors make entry and exit easy. In addition, the cab mounts through existing tractor holes, so normal installation does not require drilling.
Most of all, Cab 11826 gives LS G-Series owners a simple way to add useful foul-weather coverage to a tractor built for year-round work.
Original Tractor Cab 11826 for LS G-Series Tractors
The LS G-Series was built for many jobs. These compact utility tractors can mow, move material, run PTO tools, handle three-point equipment, and work with loaders or backhoes.
However, the standard open operator station leaves the driver exposed to the weather. So, Original Tractor Cab designed Cab 11826 to surround much of that area.
The result is more operator cover when outdoor conditions change.
Fits Four LS G-Series Models
Original Tractor Cab lists Cab 11826 for the LS G3033, G3033H, G3038, and G3038H.
These tractors share the basic G-Series platform, yet engine power and transmission type vary by model. Therefore, always confirm the full tractor model before ordering.
Correct model fit matters.
Cab 11826 Does Not Fit the LS XG Series
The G-Series and XG Series names may look similar. However, Cab 11826 is not made for the LS XG Series.
Therefore, do not order this cab for an XG3025, XG3032, XG3037, XG3135, XG3140, or another XG tractor based only on similar size or appearance.
Use Cab 11826 only on the listed G-Series applications.
Check the Tractor Before You Buy
Find the tractor model and serial information before placing an order. Then, compare your machine with the current Cab 11826 installation guide.
Also, inspect any loader, seat, controls, hydraulic parts, lights, or owner-added accessories that may change cab clearance.
Ask about fit before making tractor changes.
Fully Enclosed LS G-Series Weather Cab
Cab 11826 gives the operator much more coverage than an open canopy. The hard roof covers the top while clear panels help close the front, sides, and rear.
As a result, the enclosure can help reduce direct exposure to normal rain, snow, sleet, and wind.
Still, the cab is not sealed or heated.
ABS Plastic Hardtop
A molded ABS plastic roof forms the top of Cab 11826. The hardtop keeps its shape and gives the operator solid overhead weather cover.
Therefore, it helps block direct rain, snow, sleet, and overhead sun. The roof can also remain in place when the side doors are removed for warm-weather use.
The hardtop is not a certified safety structure.
Clear Lexan Windshield
Good sight is vital on a compact tractor. So, Cab 11826 uses clear shatter-resistant Lexan plastic for the standard windshield.
The windshield helps block direct wind and weather while keeping the forward work area in view. In addition, its forward slope helps reduce glare and contact with falling rain or snow.
Keep the windshield clean during every job.
Clear Side Doors and Rear Curtain
Clear shatter-resistant Lexan material is also used in the side doors and rear curtain. As a result, the operator can see through key areas around the cab.
That matters when you use a loader, back up to a tool, or work close to buildings and trees.
Always turn and look before moving the tractor.
Optional Safety Glass Windshield
The standard Lexan windshield can be replaced with an optional safety glass windshield. The glass option is sold separately.
Therefore, owners who want a glass front panel can upgrade Cab 11826 without replacing the full enclosure.
Use only a windshield made for this cab.
Windshield Wiper Option
A compatible wiper kit can also be added when the required safety glass windshield is installed. This can help during rain, wet snow, and other work that puts moisture on the front glass.
However, a wiper does not make poor visibility safe. Stop the tractor if you cannot clearly see the work area.
Never operate with a blocked windshield.
Hinged Doors With Latches
Cab 11826 has hinged doors with latches. Therefore, getting into and out of the enclosure remains quick and simple.
The doors help close the sides during cold-weather work. Yet they can also be removed when the weather gets warm.
Check each latch before starting work.
Remove the Doors for Summer Use
Warm weather changes what you need from a tractor cab. So, Cab 11826 lets you remove the doors during summer.
Once the doors are off, the hardtop can serve as an overhead sunshade. This gives the cab useful seasonal flexibility.
Store removed doors where they will stay clean and safe.
Hardtop Can Double as a Sunshade
Direct summer sun can make long tractor jobs harder. Therefore, leaving the ABS roof in place can add shade above the operator.
Open sides also allow much more airflow than the winter enclosure. As a result, the cab can adapt to warmer conditions without removing the full frame.
Watch for heat on very hot days.
No Holes to Drill During Normal Installation
Cab 11826 mounts through existing holes on the compatible LS G-Series tractor. So, normal installation does not require drilling the tractor.
That helps reduce permanent changes to the machine. It also makes the model-fit design easier to install than an enclosure that needs custom mounting points.
Follow the current instructions from start to finish.
Model-Fit Steel Support Frame
A set of feet, braces, front posts, rear posts, ROPS brackets, crossbars, and a top frame supports the enclosure.
These parts position the roof and clear panels around the G-Series operator station. Therefore, correct placement of each bracket matters.
Do not swap parts from another cab model.
ROPS Brackets Are Part of the Cab Mounting System
Cab 11826 includes right and left ROPS brackets as part of its model-fit frame. These brackets help locate and support the cab around the tractor.
However, the enclosure does not replace the LS rollover protective structure. Never remove, cut, drill, bend, or weaken the factory ROPS to make the cab fit.
Keep the tractor safety system intact.
Cab 11826 Is Not a ROPS
The steel frame may look strong, but it supports a weather enclosure. It does not provide certified rollover protection.
Likewise, the ABS roof and clear panels do not turn the tractor into a certified protective cab.
Use the factory ROPS and seat belt as LS directs.
About Three to Four Hours for Installation
Original Tractor Cab lists normal Cab 11826 installation at about three to four hours.
However, tractor condition, tools, accessories, and installer experience can change the time. So, read the instructions first and allow enough time to work with care.
Never rush cab assembly.
About 45 Minutes for Seasonal Removal
Original Tractor Cab lists cab removal at about 45 minutes after the first installation. Therefore, the enclosure can be removed when the season or job calls for an open tractor.
Actual removal time can vary. Still, the model-fit design makes seasonal use practical.
Keep removed hardware together for the next installation.
Rain Protection for LS G-Series Tractor Work
Rain can arrive before a job is done. The ABS hardtop, windshield, doors, and rear curtain help reduce direct rain around the operator.
However, Cab 11826 is not a sealed waterproof room. Wind-driven water may enter through normal openings.
Stop working during unsafe storms.
Snow Protection for Winter Jobs
Compact tractors often work when snow is on the ground. A loader, blade, or other compatible tool can keep an LS G-Series tractor busy through winter.
Meanwhile, Cab 11826 helps reduce the amount of blowing and falling snow that reaches the operator.
That can make cold work more comfortable.
Sleet and Cold Wind Protection
Cold wind can make an open tractor uncomfortable very fast. Sleet can also strike the operator and coat tractor surfaces.
So, the enclosure places a useful barrier around much of the operator station. Yet air can still enter through normal cab gaps.
Wear clothing made for the outdoor temperature.
The Cab Is Not Heated
Cab 11826 does not include a heater. Instead, it works by reducing direct exposure to the weather.
As a result, less wind may improve comfort even though the air inside remains cold.
Take warm-up breaks when needed.
Cab 11826 Is Not Certified Hail Protection
The ABS roof provides useful overhead weather cover. However, it is not a certified hail or falling-object protective structure.
Therefore, seek proper shelter during severe hail, lightning, or dangerous wind.
Do not rely on the hardtop during a severe storm.
Not Certified Debris Protection
The Lexan panels help block normal weather. However, they are not certified guards for rocks, branches, broken tools, or other flying debris.
Keep factory shields in place. Also, keep people away from active mower, loader, PTO, and other work areas.
The cab does not remove machine hazards.
Clear Panels Need Proper Care
Clear plastic can scratch if dirt is rubbed across its surface. So, rinse away loose grit before wiping the panels.
Then, clean them with materials allowed by the current cab instructions. Avoid harsh methods that can cloud or damage the clear surface.
A clean panel gives you a better view.
Inspect the Cab Before Each Season
Check the roof, frame, mounting points, doors, latches, windshield, rear curtain, and hardware before heavy seasonal use.
Next, make sure no loose cab part can contact a control, tire, hydraulic part, hot surface, or moving attachment.
Repair problems before operating the tractor.
Loader and Backhoe Use With the LS G-Series
The G-Series could work with front loaders and backhoes. Therefore, many used tractors now have extra equipment installed.
Added equipment can change clearance around the cab. So, check the actual tractor and every attachment before you operate.
Never assume attachment fit from the tractor model alone.
Watch Loader Movement
A front loader moves through a large range. Hydraulic lines and loader parts also move as the boom rises and lowers.
Therefore, test the full loader movement from a safe position after cab installation. No loader part or hose should rub against the enclosure.
Stop use if interference occurs.
Why Buy LS Cab 11826 Direct From Original Tractor Cab?
Original Tractor Cab makes Cab 11826. So, buying direct connects you with the company behind the enclosure.
You can browse our LS tractor cab and sunshade collection for other LS weather products.
You can also compare our tractor cab enclosures for other compact, lawn, and garden tractors.
Before assembly, review our cab installation manuals for current product instructions.
If your tractor has been changed or you have a fit question, use our Original Tractor Cab contact page before ordering.
LS G3033, G3033H, G3038 & G3038H Tractor Specifications
The LS G-Series tractors that fit Cab 11826 include two power levels and two main transmission choices.
The G3033 and G3033H are 33-horsepower models. Meanwhile, the G3038 and G3038H raise gross engine power to 38 horsepower.
The letter H marks the hydrostatic versions.
LS G3033 Engine
The G3033 uses an LS L3BL three-cylinder diesel engine. Factory literature lists gross power at 33 horsepower.
Engine displacement is 116.9 cubic inches, or about 1.9 liters. In addition, the liquid-cooled engine reaches rated power at 2,600 rpm.
The G3033 is the gear-drive 33-horsepower model.
LS G3033H Engine
The G3033H uses the same 33-horsepower class of LS three-cylinder diesel power.
However, the H model pairs that engine with hydrostatic drive instead of the synchro shuttle transmission used in the G3033.
That gives buyers two drive styles on the same basic power level.
LS G3038 Engine
The G3038 moves up to an LS L3AL three-cylinder diesel. Factory literature lists gross engine power at 38 horsepower.
Displacement is 122.2 cubic inches, or about 2.0 liters. Like the smaller engine, it is liquid cooled and rated at 2,600 rpm.
The extra power also raises available PTO output.
LS G3038H Engine
The G3038H uses the 38-horsepower LS diesel with hydrostatic transmission.
Therefore, it combines the higher G-Series engine rating with pedal-controlled hydrostatic travel.
That setup can be useful for loader work and jobs with many speed changes.
Gear or Hydrostatic Transmission
LS offered the G-Series with two main transmission choices. The G3033 and G3038 use a synchro shuttle transmission with 12 forward and 12 reverse speeds.
In contrast, the G3033H and G3038H use hydrostatic drive with three ranges.
Choose the correct model when ordering service parts.
G3033 and G3038 Synchro Shuttle
The 12-forward and 12-reverse synchro shuttle gives gear-model operators a broad range of travel speeds.
That can suit field work, loader jobs, and jobs where a chosen gear is useful.
Always stop or shift as the LS manual directs.
G3033H and G3038H Hydrostatic Drive
Hydrostatic models use three ranges. This lets the operator vary travel speed without selecting one of the 12 gear-drive speeds.
Therefore, H models can work well when the tractor must change speed or direction often.
Loader work is one common example.
33 and 38 Gross Horsepower
The G3033 and G3033H are rated at 33 gross horsepower. The G3038 and G3038H are rated at 38 gross horsepower.
That five-horsepower difference also changes rated PTO power.
Use the rating for your exact model.
PTO Horsepower
Factory G-Series literature lists 27 PTO horsepower for the G3033 and 26 PTO horsepower for the G3033H.
Meanwhile, the G3038 is listed at 32 PTO horsepower and the G3038H at 31 PTO horsepower.
Match every PTO tool to the tractor's limits.
Independent 540 RPM Rear PTO
The G-Series uses an independent rear PTO. Standard rear PTO speed is 540 rpm.
As a result, the tractor can power many compatible rotary cutters, finish mowers, tillers, spreaders, and other PTO tools.
Keep every PTO guard in place.
Category I Three-Point Hitch
The G-Series uses a Category I three-point hitch with position control.
Factory literature lists hitch lift capacity at 1,808 pounds at the hitch end. Therefore, these tractors can handle a broad range of compact tractor tools when used within their limits.
Tool weight and balance still matter.
11.9 GPM Total Hydraulic Flow
Factory data lists 7.4 gallons per minute from the implement pump and 4.5 gallons per minute from the steering pump.
Together, total hydraulic flow is listed at 11.9 gallons per minute.
Keep the hydraulic system clean and serviced.
Hydrostatic Power Steering
The G-Series uses hydrostatic power steering. Therefore, steering effort stays manageable during loader work and other jobs with frequent turns.
Power steering can make work easier, but it does not change safe travel speed.
Slow down before turning.
Wet Multi-Disc Brakes
LS equipped the G-Series with wet multi-disc brakes. These brakes work within the tractor system rather than as open external brake surfaces.
However, every brake system still needs proper service.
Never use a tractor with a known brake fault.
Four-Wheel Drive on Common G-Series Configurations
Four-wheel drive gives these compact tractors more traction for loader work, snow, mud, and loose ground.
The G3033, G3033H, and G3038H are commonly listed as four-wheel-drive machines. The G3038 was also offered in a two-wheel-drive configuration.
Confirm the drive setup on your tractor.
7.4-Gallon Fuel Tank
Factory data lists G-Series fuel capacity at 7.4 gallons.
The diesel tank gives the tractor useful work time without making the machine much larger.
Use clean diesel fuel and follow LS service guidance.
65.9-Inch Wheelbase
Common four-wheel-drive G-Series models use a wheelbase of about 65.9 inches.
That compact wheelbase helps keep the tractor easy to use around property obstacles. Yet the machine remains large enough for serious loader and three-point work.
Attachments increase the working footprint.
About 117.6 Inches Long
Published G-Series dimensions place common models at about 117.6 inches long.
Width varies with tires and setup. For example, published G3033 and G3033H data lists a minimum-style tractor width near 42.6 inches.
Always measure the actual machine for tight spaces.
About 90.2 Inches to the ROPS
Published data lists ROPS height near 90.2 inches on common G3033 and G3033H configurations.
Cab parts can change the tractor's shape and clearance. Therefore, measure the completed tractor before entering a garage, trailer, shed, or other low area.
Allow extra overhead room.
G-Series Tractor Weight
Published data lists the G3033 at about 2,690 pounds and the G3033H near 2,710 pounds before many common attachments.
G3038 weight also varies by drive and transmission configuration. A loader, backhoe, ballast, cab, and tools can add a great deal of weight.
Check trailer and surface limits before transport.
Loader Capability
LS offered a front loader for the G-Series. Published LL3102 loader data lists lift capacity near 1,600 pounds at full height at the pivot pin.
However, loader capacity depends on the exact loader, setup, measurement point, ballast, and tractor configuration.
Use the manual for your installed loader.
Backhoe Capability
A compatible LS backhoe was also available for the G-Series.
Published LB1102 data lists a digging depth of about 76.3 inches and bucket digging force near 2,817 pounds.
Backhoe installation changes tractor size and balance.
Use the Correct Ballast
Loader and backhoe work can shift tractor weight. Therefore, use ballast and tire settings approved for the job.
The cab does not increase tractor capacity or stability.
Stay within all LS limits.
Factory LS G-Series Information
The G3033, G3033H, G3038, and G3038H are previous LS models. Therefore, owners should use the factory manual for exact operating, maintenance, and safety information.
You can find the G3033, G3033H, G3038, and G3038H in the official LS Tractor owner manual library.
For current manufacturer support and LS Tractor information, visit the official LS Tractor USA website.
The History of Original Tractor Cab Company
Original Tractor Cab began in 1939. At that time, Indiana farmer Stanley Williams needed more cover from bad weather while working on his tractor.
So, Stanley made a cab for his own use. Other farmers soon saw his idea and wanted similar weather protection.
A practical farm solution began to grow into a business.
Born From a Need on the Farm
Farm work did not stop when the weather turned cold or wet. Rain, snow, wind, and cold were simply part of the job.
Therefore, Stanley's first cab solved a problem he knew well. It put a useful barrier between the operator and much of the weather.
Other farmers saw the value right away.
A Farm Idea Becomes a Business
Word about Stanley's cab began to spread. Then, a small farm magazine ad helped the idea reach more tractor owners.
The response showed that many farmers had the same need. As a result, one farm-built cab became the base of a new American company.
Original Tractor Cab traces its start to 1939.
Products Made for Real Outdoor Work
The early company grew around a clear idea. Make practical weather products for people who work outside.
That goal remained important as tractors changed. Therefore, Original Tractor Cab kept adapting its products to new equipment.
Real outdoor work continued to shape the product line.
Original Tractor Cab During World War II
World War II changed the young company's work. Normal tractor cab production stopped as manufacturing shifted to support the war effort.
During that period, the company made backpacks and other needed military items. Afterward, Original Tractor Cab returned its focus to outdoor equipment.
Its manufacturing story continued.
New Machines Create New Cab Needs
Tractors and outdoor equipment changed greatly after the war. Lawn tractors, garden tractors, compact tractors, snowblowers, and new mower types became common.
So, Original Tractor Cab expanded beyond its early farm tractor products. Different machines called for different types of operator weather cover.
The product range grew with the equipment market.
Snowblower Cabs Expand the Product Range
The next generation of the Williams family saw another weather problem. Walk-behind snowblower users worked directly in cold wind and blowing snow.
Therefore, the company developed cab products for snow equipment. Lawn and garden tractor weather products also became an important part of the business.
The original idea had found new uses.
Sunshades Add Warm-Weather Cover
Winter weather was only part of the problem for equipment operators. Hot summer sun could also make long outdoor jobs hard.
So, the Williams family added sunshade products to the company line. That gave customers useful overhead cover during warm-weather work.
Original Tractor Cab could now serve more seasons.
Three Generations of the Williams Family
Three generations of the Williams family helped carry Original Tractor Cab forward.
Each generation responded to new equipment and new customer needs. However, the basic idea stayed easy to understand.
Help people work outdoors with more cover from the weather.
From Early Farm Tractors to LS Compact Tractors
The LS G3033 and G3038 are far different from the tractor Stanley Williams used in 1939.
Yet the operator still faces rain, snow, sleet, wind, cold, and sun. Therefore, the basic reason for adding Cab 11826 remains much the same.
The tractors changed, but the weather did not.
Made in the USA Since 1939
Original Tractor Cab remains based in Arlington, Indiana. Today, the company makes hardtop tractor cabs, soft enclosures, sunshades, snowblower cabs, mower products, and related accessories.
Meanwhile, direct sales make it easier for equipment owners to buy from the company behind the product.
Cab 11826 carries that long American manufacturing story to LS G-Series owners.
Read more on our Original Tractor Cab company history page.
LS G-Series Cab 11826 Questions
What tractors fit Original Tractor Cab 11826?
Cab 11826 fits the LS G3033, G3033H, G3038, and G3038H compact tractors.
Will Cab 11826 fit an LS XG Series tractor?
No. Original Tractor Cab states that Cab 11826 will not fit the LS XG Series.
Is Cab 11826 a hardtop cab?
Yes. Cab 11826 is a fully enclosed weather cab with a molded ABS plastic hardtop.
What are the clear cab panels made from?
Clear shatter-resistant Lexan plastic is used for the standard windshield, side doors, and rear curtain.
Can I add a safety glass windshield?
Yes. The standard Lexan windshield can be replaced with a compatible optional safety glass windshield sold separately.
Can I add a windshield wiper?
A compatible wiper kit is available for use with the required safety glass windshield. Check current accessory fit before ordering.
Does Cab 11826 require drilling?
No. Normal installation on the correct tractor uses existing mounting holes, so drilling is not required.
How long does Cab 11826 take to install?
Original Tractor Cab lists normal installation at about three to four hours.
How long does Cab 11826 take to remove?
Original Tractor Cab lists approximate removal time at 45 minutes after the cab has been installed.
Can I remove the doors in summer?
Yes. The doors can be removed during warm weather so the hardtop can serve as an overhead sunshade.
Does Cab 11826 help protect from rain?
Yes. The enclosure helps reduce direct exposure to normal rain. However, the cab is not a sealed waterproof compartment.
Does Cab 11826 help protect from snow and sleet?
Yes. The roof and enclosure help reduce direct exposure to normal falling and blowing snow and sleet.
Does Cab 11826 help block wind?
Yes. The enclosure can reduce direct wind around the operator. Still, it is not airtight or heated.
Does Cab 11826 provide hail protection?
No. Cab 11826 is not certified hail or falling-object protection. Seek proper shelter during severe weather.
Does Cab 11826 provide rollover protection?
No. Cab 11826 is a weather enclosure. It does not replace the LS tractor's ROPS or provide certified rollover protection.
Does the cab protect from loader, mower, or PTO debris?
No. The roof and clear panels are not certified impact or debris guards. Keep all factory shields in place.
How much horsepower does the LS G3033 have?
The LS G3033 and G3033H are rated at 33 gross engine horsepower.
How much horsepower does the LS G3038 have?
The LS G3038 and G3038H are rated at 38 gross engine horsepower.
What is the difference between the G3033 and G3033H?
Both use the 33-horsepower engine class. The G3033 uses a 12-forward and 12-reverse synchro shuttle transmission, while the G3033H uses a three-range hydrostatic transmission.
What is the difference between the G3038 and G3038H?
Both use the 38-horsepower engine class. The G3038 uses a synchro shuttle transmission, while the G3038H uses hydrostatic drive.
What is the G-Series three-point hitch capacity?
Factory literature lists the Category I three-point hitch at 1,808 pounds of lift capacity at the hitch end.
Is Cab 11826 a genuine LS Tractor OEM cab?
No. Cab 11826 is an aftermarket product made by Original Tractor Cab Co., Inc. for compatible LS G-Series tractors.
Non-OEM and Liability Disclaimer
This is an aftermarket product produced by the Original Tractor Cab Co. Inc., it is not a genuine OEM item. This product will only protect from elements not rollover or debris.
Original Tractor Cab Co., Inc. is not affiliated with, sponsored by, or endorsed by LS Tractor or LS Mtron. LS Tractor, LS Mtron, G3033, G3033H, G3038, G3038H, related logos, trademarks, and model names remain the property of their respective owners. Brand and model references on this page are used only to identify intended product compatibility.
Cab 11826 is intended for compatible LS G3033, G3033H, G3038, and G3038H tractors. It does not fit the LS XG Series. Owners must confirm the exact tractor model, ROPS, controls, attachments, loader, hydraulic parts, and current machine configuration before purchase and installation.
Cab 11826 is designed to help reduce direct exposure to normal rain, snow, sleet, wind, cold, and overhead sun. It does not create a sealed, heated, waterproof, impact-resistant, or certified protective operator compartment.
The ABS roof, steel cab frame, Lexan windshield, doors, and rear curtain do not provide certified rollover, falling-object, collision, hail, or debris protection. Never use Cab 11826 as a ROPS, FOPS, impact shield, or machine guard.
Never remove, drill, cut, bend, weld, weaken, or alter the factory ROPS to install the cab. Follow the LS operator manual and the current Original Tractor Cab installation instructions.
Before use, check the steering, brakes, pedals, PTO controls, hydraulic controls, three-point controls, loader movement, doors, visibility, cooling airflow, ROPS clearance, and operator exit. Stop using the tractor if any cab part blocks normal operation.
Attachments can change tractor weight, width, length, balance, stability, traction, and handling. Therefore, follow the correct LS instructions for loaders, backhoes, mowers, PTO tools, ballast, tire chains, and other equipment.
Never exceed tractor, loader, backhoe, hitch, PTO, axle, tire, or attachment ratings. Installing Cab 11826 does not increase any factory tractor capacity.
California Proposition 65 Warning
WARNING: Cancer and Reproductive Harm — www.P65Warnings.ca.gov.
This product and the equipment on which it is installed may expose users to chemicals known to the State of California to cause cancer, birth defects, or other reproductive harm. Possible sources may include diesel engine exhaust, fuel, oils, batteries, plastics, vinyl, metals, electrical components, and other tractor or cab materials. Follow all product and equipment safety instructions. Operate engine-powered equipment outdoors with proper ventilation, wash hands after handling applicable materials, and avoid unnecessary exposure.
